|NRP-192PRi Ultra PoE Extender Built-In Voltage Booster
3 Ethernet 10/100/1000Base-T + Ultra PoE 95W/60W/30W + VDC Booster
The Gigabit Ultra PoE Extender, Model NRP-192PRi, is designed to extend connection distances from
a PSE (Power Source Equipment) to a PD (Powered Device) another 100 m via Cat5e or Cat6 cable.
The transmission is carried out at a distance of 200 to 500 meters or more by cascading these extenders on a network.
The built-in booster compensates for the voltage drop (48VDC) on the twisted pair with the cascade connection.
Similar repeaters of other manufacturers do not have this characteristic,
so the use of more than two such repeaters in the chain is impossible.
Device doesn't need any additional power supply, because it uses a transit PoE from the input cable,
while its power consumption does not exceed 3 watts. PoE Extender usually works with any PSE or PD devices.
This solves the problem of "only 100 m for PoE and data" and there is a possibility to install
IP equipment (IP Cameras, IP Access Controls, and Wireless Access Points) in the places most suitable for this.
The advantages of NRP-192PRi over other existing analogues:
· Support for Gigabit Ethernet 10/100/1000-BaseT;
· Two output PSE ports 75W/60W/30W/15W instead of one in other devices;
· The input PD port works with power supplies from 30 to 95W;
· Voltage drop compensation on twisted pair (built-in Voltage Booster);
· The industrial grade device with wide operating temperature range;
· The rugged outdoor weatherproof housing is rated to IP65.
The devices are easy to install and operate in Plug & Play mode.
The housing has three waterproof RJ45 connectors for one input port and two output ports.
The input port is connected to the PSE equipment (PoE Injector or PoE Switch) and the output ports to the equipment
PD (IP Cameras, IP Access Controls, and Wireless Access Points) or to the next extender during cascading multiple PoE extenders.
| 3 ports Ethernet 10/100/1000Base-T with supporting Ultra PoE 95W/60W|
| Switch Fabric 6Gbps, Jumbo Frame 10Kb, 8K MAC, 1Mb buffer|
| Complies with IEEE 802.3/802.3u/802.3ab/802.3x Flow Control è Back-pressure|
| Support 10/100/1000 auto-negotiation and auto-MDIX|
| Extends an existing PoE connection beyond the 100m (328-ft.) limit|
| Cascading of multiple devices into a chain is possible|
| Voltage drop compensation on twisted pair (built-in Voltage Booster)|
| 1 port PD IN up to 95W + 2 ports PSE OUT 75W/60W/30W/15W|
| POE Pin Assignment: 1/2(+), 3/6(-) and 4/5(+), 7/8(-)|
| Power Consumption: 3W, Does not require an additional power supply|
| Overload current and reverse polarity protection|
| Housing IP65/IK10, Wall mounting, Waterproof RJ45 connectors|
| Operating Temperature: -40 ~ 75°C|
| Dimensions: 190x85x65mm; MTBF > 500000 hrs|
| ||The number of Extenders in the chain and Maximum wattage of the PoE port (PSE OUT)|
when NRP-192PRi is connected using only one output port
|PoE (PD IN)||1 (100-200m)||2 (200-300m)||3 (300-400m)||4 (400-500m)|
|30W||22W||16W||10W|| - |
|Models||Part Number||Features |
|NRP-192PRi||63P2G9EI||Extender: 3 Ethernet 10/100/1000M Ultra PoE 95W/60W/30W, Booster, 1 PD/ 2 PSE|